Layer 3 Switch IOS for GNS3 free download

Question

Adding a Layer 3 Switch in GNS3

Nội dung chính Show

Adding a Layer 3 Switch in GNS3
How to Use Layer 3 Switch on GNS3
How to Add L3 Switch in GNS3
GNS3 L3 Switch Configuration ⇒ Video
Final Word
Related Articles
Does GNS3 support switching?
How install IOS switch in GNS3?
What is Cisco IOU?
What is IOU in GNS3?

To add a layer 3 switch in GNS3, you need to perform the following steps:

Once you have downloaded the Cisco 3640 series IOS image, open the Preferences window by clicking the Edit and then Preferences in the GNS3 console.

In the Preferences window, select IOS routers in the left pane. Here, you will see all the added IOS router templates. To add a new IOS router template, click New as shown in the following figure.

On the New IOS router template window, select the New Image radio button.

Click Browse and navigate to the location where you have downloaded the 3640 IOS image file, and then select it.

In the IOS Image message box, click Yes to decompress the selected image, and then click Next.

On the Name and platform page, type a name such as Layer 3 Switch in the Name text box, select the This is an EtherSwitch router check box and then click Next.

On the Memory page, accept the default memory size or set the desired value, and click Next.

On the Network adapters page, select NM-16ESW from the slot 0 drop-down list and then click Next.

On the Idle-PC Finder page, click Finish and close the Preferences window.

You will see that a layer 3 switch in GNS3 console has been added. Drag it to the work view area.

Right-click layer 3 switch (ESW1) and select Start to start it.

Once it is started, select and right-click again it and select Console to open its console.

On the ESW1 console, type the following commands to verify that it works as a Layer 3 switch.

ESW1(config)#hostname Switch2

Switch2#show vlan database

The following figure shows that the preceding commands are successfully executed on the layer 3 switch that you have added in GNS3.

Source

https://protechgurus.com/use-add-layer-3-switches-gns3/

In our previous article, we added the Layer 2 Switch IOS image. In this article, we will configure Layer 3 Switch IOS image. As you know, L2 Switches only transmit packets according to the MAC address table.

Layer 3 switches also use the MAC address table and additionally serve as routing.

How to Use Layer 3 Switch on GNS3

Installing L3 Switch to GNS3 is almost the same as installing a Cisco Router. To perform Switching-based operations with the simulator, you need to use the L3 Switch.

With Layer 3 Switches, you can perform the VLAN, 802.1Q Trunking, and InterVLAN Routing.

Cisco Layer 3 Switch IOS Download

First, download the Switch IOS image to your computer by clicking the button below.

IOS Download

How to Add L3 Switch in GNS3

After downloading the L3 Switch IOS image to your computer, open the network simulator, and follow the steps below.

Step 1

To add a new device, click Edit.

Step 2

From the Edit menu, click Preferences.

Step 3

In the General Preferences window, click the IOS Routers tab.

Step 4

Previously we added L2 Switch from Qemu VMs. To add L3 Switch, click the New button in the IOS Router templates window.

Step 5

In the IOS Image window, select New Image, then click Browse.

Step 6

Select the IOS you downloaded from the above button and click the Open button.

Step 7

The GNS3 program asks if you want to copy the IOS to the default image folder, click Yes.

Step 8

After adding Switch IOS, click Next to continue.

Step 9

In this step, select “This is an EthernetSwitch Router” and then click Next.

Step 10

Leave the RAM value of Layer 3 Switch as default and click Next.

Step 11

In the Network Adapters window, select the NM-16ESW interface in Slot 0 and continue to the next step.

Step 12

Click the Idle-PC Finder button to select the optimal value for your computer’s processor performance for Layer 3 Switch IOS.

Step 13

Wait while calculating the Idle-PC value.

Step 14

After determining the optimal Idle-PC value for IOS, click OK to continue.

Step 15

As you can see in the image below, the Layer 3 Switch (EtherSwitch Router) has added successfully.

Step 16

Drag and drop the Switch to the GNS3 workspace.

Step 17

Create a topology as follows and double click on L3 Switch.

Step 18

Now, to test the Switch, execute the show vlan-switch command in the CLI command interface.

Configure the switch by executing the following commands.

ESW1# conf t
ESW1(config)#interface vlan 1
ESW1(config-if)#ip address 192.168.10.1 255.255.255.0
ESW1(config-if)#no shutdown
ESW1(config-if)#exit
ESW1(config)#infterface fastethernet0/0
ESW1(config-if)#no shutdown
ESW1(config-if)#exit
ESW1(config)#exit
ESW1#

Step 19

Configure the VPCS and then ping the VLAN1 interface to test the connection as follows.

Step 20

You can see that pinging between VPCS is successful.

Show Commands

ESW1#show running-config
Building configuration...

Current configuration : 2035 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
no service dhcp
!
hostname ESW1
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
memory-size iomem 5
no ip routing
no ip icmp rate-limit unreachable
!
!
no ip cef
no ip domain lookup
!
!
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
vtp file nvram:vlan.dat

!
!
ip tcp synwait-time 5
!
!
!
interface FastEthernet0/0
description *** Unused for Layer2 EtherSwitch ***
!
interface FastEthernet0/1
description *** Unused for Layer2 EtherSwitch ***
shutdown
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface Vlan1
ip address 192.168.10.1 255.255.255.0
no ip route-cache
!
no ip http server
no ip http secure-server
!
ip forward-protocol nd
!
!
no cdp log mismatch duplex
!
!
control-plane
!
!
mgcp behavior g729-variants static-pt
!
!
banner exec ^C

***************************************************************
This is a normal Router with a SW module inside (NM-16ESW)
It has been preconfigured with hard coded speed and duplex

To create vlans use the command "vlan database" from exec mode
After creating all desired vlans use "exit" to apply the config

To view existing vlans use the command "show vlan-switch brief"

Warning: You are using an old IOS image for this router.
Please update the IOS to enable the "macro" command!
***************************************************************

^C
!
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
login
!
!
end

ESW1#

ESW1#show ip int br
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES unset up up
FastEthernet0/1 unassigned YES unset administratively down down
FastEthernet0/2 unassigned YES unset up down
FastEthernet0/3 unassigned YES unset up down
FastEthernet0/4 unassigned YES unset up down
FastEthernet0/5 unassigned YES unset up down
FastEthernet0/6 unassigned YES unset up down
FastEthernet0/7 unassigned YES unset up down
FastEthernet0/8 unassigned YES unset up down
FastEthernet0/9 unassigned YES unset up down
FastEthernet0/10 unassigned YES unset up down
FastEthernet0/11 unassigned YES unset up down
FastEthernet0/12 unassigned YES unset up down
FastEthernet0/13 unassigned YES unset up down
FastEthernet0/14 unassigned YES unset up down
FastEthernet0/15 unassigned YES unset up down
Vlan1 192.168.10.1 YES manual up up
ESW1#

ESW1#show vlan-switch

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/1, Fa0/2, Fa0/3
Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 1002 1003
1002 fddi 101002 1500 - - - - - 1 1003
1003 tr 101003 1500 1005 0 - - srb 1 1002
1004 fdnet 101004 1500 - - 1 ibm - 0 0
1005 trnet 101005 1500 - - 1 ibm - 0 0

GNS3 L3 Switch Configuration ⇒ Video

You can watch the video below to use Switch on GNS3 and also subscribe to our YouTube channel to support us!

Final Word

In this article, we examined the GNS3 Layer 3 Switch settings, the most popular network simulator program used to prepare for Cisco exams. Thanks for following us!

♦ GNS3 VM Network Settings
♦ How to Install Router in GNS3 VM
♦ How to Use VLANs in Layer 2 Switch
♦ How to Run GNS3 in Linux
♦ How to Configure a Cisco Switch

Does GNS3 support switching?

One common misconception about GNS3 is that GNS3 does not support advanced switching options. While this was true in the past, GNS3 now supports options such as: Etherchannel. PVST+

How install IOS switch in GNS3?

STEP 1: Open the GNS3 VM. Navigate to Edit > Preferences > Dynamips > IOS routers. STEP 2: Click on the “New” button and select “New Image”. STEP 3: Select the downloaded image of the router to install on GNS3 VM by clicking on “Browse”.

What is Cisco IOU?

Cisco IOS on UNIX (IOU) is a fully working version of IOS that runs as a user mode UNIX (Solaris) process. IOU is built as a native Solaris image and run just like any other program. IOU supports all platform independent protocols and features.

What is IOU in GNS3?

IOU is IOS on Unix (Solaris, if you want to be specific). It's a version of IOS compiled to run on workstations. It's faster and lighter than emulation. Cisco transitioned to IOL images, which are x86-64 compatible versions of IOS that natively run in Linux.

Công Nghệ Ios